COVID-19 Status: AVTECH remains fully operational and is ready to support our customers. Click for more details.

Knowledge Base  /  Release Notes  /  Room Alert Firmware  /  Current Models

Room Alert 3 Wi-Fi Firmware Release Notes

Firmware updates for your Room Alert products are available at RoomAlert.com.

v2.0.1

April 1, 2020
  • Fixed an issue that prevented the device from properly saving a mail server IP address.

v2.0.0

August 15, 2018
  • Added alarm configuration options.
    • Added ability to set custom sensor names for digital and switch sensors.
    • Added ability to set high & low thresholds on digital sensors.
    • Added ability to set switch sensor to Alarm on Open or Closed.
    • Added ability to apply adjust value to digital sensor readings.
    • Updated alarm icons in Status page to reflect the sensor’s alarm status, based on set thresholds.
    • Added ability to trigger an alarm if the external digital sensor is disconnected.
  • Added SMTP Email capabilities.
    • Added ability to configure SMTP Email settings.
    • Added capability to send emails in response to a triggered or cleared alert.
  • Added support for dew point on Digital Temperature & Humidity Sensors.
  • Added support for Digital Temperature & Analog Sensors.
    • Added support for analog custom scale.
  • Added support for Digital Active Power Sensors.
  • GoToMyDevices.com has moved to Account.RoomAlert.com. The firmware has been updated to support and reference this change.
  • Updated the RoomAlert.com push functionality so that a push is triggered on same conditions as other Room Alert models.
  • Added date & time configuration.
    • Added capability to select timezone, time display, and time format.
    • Added option to sync Room Alert 3 Wi-Fi to a custom time server.
  • Added ability to reset Room Alert 3 Wi-Fi to factory defaults through web interface.
  • Added ability to save temperature scale as Fahrenheit or Celsius.
  • Made updates to improve network stability and security.

v1.1.1

September 8, 2016

AVTECH Device ManageR v6.3.3 or higher or Device Discovery Utility v4.3.1 or higher is required for this update. Please be sure any web browsers currently accessing the unit are closed to be sure all files are updated correctly.

  • Resolved an issue that could cause the Room Alert 3 Wi-Fi to not be recognized by GoToMyDevices if the wireless soft AP was disabled
  • Updated the default status page refresh rate to 60 seconds
  • Added an upper limit to the status page refresh rate field
  • Updated sensor-based push triggers to match other Room Alert models. Pushes now occur on:
    • 2 degrees Celsius temperature change
    • 5 %RH humidity change
    • Sensor connect / disconnect

v1.1.0

November 20, 2015

AVTECH Device ManageR v6.3.3 or higher or Device Discovery Utility v4.3.1 or higher is required for this update. Please be sure any web browsers currently accessing the unit are closed to be sure all files are updated correctly.

  • Resolved an issue that could cause the Room Alert 3 Wi-Fi to drop off the Wi-Fi network and require a power cycle or reboot to reconnect again.
  • Updated all push triggers to use the same logic as other Room Alert models, so data pushed to GoToMyDevices is consistent across all Room Alert monitors.
  • Added a retry delay for failed pushed to GoToMyDevices.
  • Updated push logic to ensure that a push triggered while the delay timer was in progress is sent immediately when the delay timer expires.
  • Resolved an issue that could cause sensors to stop updating if the temperature on a Temp/Humidity Sensor when below 32F.
  • Resolved an issue that could cause sensors to stop updating if too many spikes were detected.
  • Corrected the sensor labels displayed on the Status page.
  • Added more information to the header on the Status page to make it more consistent with what is displayed on other Room Alert monitors.

v1.0.0

Release Date
  • First official release of Room Alert 3 Wi-Fi firmware.
Facebooktwitterredditpinterestlinkedinmail